Header GWEIKE România – Delta Machine
Bara de trimitere către cealaltă limbă

Shipped across the EU from Bucharest

Six laser processes in one machine GWEIKE M3 ULTRA

A 1200 W fibre source and a 130 W CO₂ tube in a single enclosure: CNC metal cutting, laser welding, laser cleaning, handheld cutting, CO₂ cutting and CO₂ engraving. One operator, one footprint, one single-phase socket.

Price excl. VAT

EXW Bucharest. Spare parts during warranty, full video tutorials and remote assistance included.

GWEIKE M3 ULTRA 6-in-1 laser machine

The machine in our Bucharest showroom, where it can be seen cutting your own material.

6 processesin a single machine
1200 W + 130 Wfibre source and CO₂ tube
1380 × 920 mmworking area
±0.02 mmrepeat accuracy on X and Y

Build your configuration

Select the options you need and see the price update.

Excluding VAT · EXW Bucharest, Romania

Options
Total, excluding VAT
Included at no extra cost
  • Spare parts shipped free of charge during warranty
  • Full video tutorial set for setup and operation
  • Remote assistance by WhatsApp and TeamViewer
Not sure which configuration fits?Ask us here, on WhatsApp

Prices exclude VAT. Quotations are issued in euro, EXW Bucharest.

24-month warranty

Two years on the machine, one year on the laser source and the CO₂ tube.

EU-wide delivery

EXW Bucharest. Transport to your address quoted on request.

Simple installation

Complete installation guide, with online support whenever you need it.

Full video course

Training on the software and on all six working modes.

What it does

Six processes, one machine

Changing between the fibre head and the CO₂ head takes about thirty seconds. The machine occupies roughly one fifth of the floor space a conventional line of separate equipment would need.

CNC metal cutting with the M3 ULTRA
FIBRE

CNC metal cutting

Up to 12 mm on carbon steel with the 1200 W fibre source, on a 1380 × 920 mm bed, driven from industrial nesting software.

Laser welding with the M3 ULTRA
FIBRE

Laser welding

From 0.2 to 5 mm. Narrow heat-affected zone, minimal distortion, and a weld that usually needs no grinding afterwards.

Laser cleaning with the M3 ULTRA
FIBRE

Laser cleaning

Rust, paint, oxide and weld discolouration removed without abrasives, chemicals or masking.

Handheld laser cutting
FIBRE

Handheld cutting

The same source on a handheld head, for parts too large or too awkward to place on the table.

CO2 cutting on non-metals
CO₂

CO₂ cutting

Up to 25 mm on non-metals: acrylic, wood, MDF, leather, textiles, rubber and foam.

CO2 engraving
CO₂

CO₂ engraving

Marking and engraving on the same materials, including on cylindrical parts with the optional rotary device.

In production

What it actually changes on the shop floor

Process change in thirty seconds

The modular design lets you swap the fibre head for the CO₂ head and adjust the parameters in under a minute, with no special tools and no lengthy recalibration. In practice this is what makes a six-process machine usable: if changing over took an hour, nobody would do it twice a day.

Changing the laser head on the M3 ULTRA

Industrial nesting software

The nesting algorithms raise sheet utilisation by 15 to 30%, including for complicated shapes. Common-line cutting reduces the number of passes, and micro-joints hold the parts in place until the programme finishes, so nothing shifts and nothing drops through.

Nesting software for the M3 ULTRA

Welding over five times faster than TIG

Clean seams, no spatter, high tensile strength and a good seal. It works on stainless steel, aluminium, copper, titanium and other metals, from very thin 0.1 mm sheet up to medium plate. On thin stainless, where TIG distorts the part, the difference is impossible to miss.

Laser welded seam

Large table, small footprint

The 1380 × 920 mm working area takes sheet up to 1380 mm wide, fed from the front or from the back, so you cut straight to the required size without secondary operations. The whole machine still fits where a single conventional cutter would stand.

M3 ULTRA working table
Options in detail

What each option actually does

None of these is compulsory, and each one can be ordered later just as well as now. They are described here so you can judge for yourself which ones your work really needs.

Rotary device

Rotary device 1,299 €+ 699 €

Extends what you can machine

Turns the machine from one that works on flat stock into one that also machines round parts. You clamp the tube or round part in the device and it rotates in sync with the laser head, so you can cut, weld, clean and engrave around the full circumference. The high-torque servo motor responds quickly, with speed deviation under 0.1%, so no vibration creeps into the toolpath.

DiametersΦ15 – 150 mm
Maximum part length1200 mm · 3000 mm at Φ15 – 50
Axial load35 kg
MotorServo, deviation < 0.1%
Size · weight990 × 157 × 191 mm · 10 kg
The rotary device at work

The rotary device at work. The clip opens at the point where it is shown.

Visual alignment system for the laser head

Visual alignment system 1,899 €+ 1,199 €

Turns guesswork into numbers

An industrial vision system that shows you on screen, in millimetres, how far the centre of the nozzle sits from the centre of the beam — two points the eye simply cannot compare. When the beam is not centred in the nozzle, the gas jet and the energy no longer fall on the same line as the cut: you get dross, bevelled edges and scrapped parts. The problem creeps in gradually, after a nozzle change or a small collision, and is usually noticed only once quality has already dropped. Alignment takes one step, with no test cuts and no adjusting by eye.

Camera resolution1920 × 1200
Recognition repeatability≤ 0.02 mm
Absolute accuracy≤ 0.05 mm
Screen4.5 inch
Power21700 battery, 4500 mAh, USB charging
Size · weight180 × 80 × 82.5 mm · approx. 1 kg
ProtectionIP64
How the visual alignment system is used

How the alignment system is used, step by step. Filmed by the manufacturer.

Screw compressor

Screw compressor + 3,400 €

Cuts your running cost

Gives you clean, dry compressed air so you can cut with air instead of bottled nitrogen. The high pressure of 1.5 MPa blows the molten metal out of the kerf, so edges come out clean and dross-free and cutting speed on steel increases. The air is certified oil-free, which protects the lenses in the cutting head. It arrives as a complete assembly: compressor, refrigerant dryer, filter and a 230 litre tank. The compressor plus any other option takes the configuration past 14,900 €, the threshold at which 400 € comes off the total.

Working pressure1.35 – 1.5 MPa, adjustable
Air flow0.25 m³/min
Tank capacity230 litres
Motor · total power3 kW · 5 kW
Supply · noise220 V single phase · 60 dB
Voltage stabiliser

Voltage stabiliser + 349 €

Recommended · protects the source

A fibre laser source is sensitive to mains fluctuation, which is why we recommend this on every installation rather than treating it as a luxury. It holds the voltage steady at 220 V no matter how much the workshop supply moves. When voltage drops or rises, the measuring circuit drives a servo motor that corrects it automatically, at more than 15 V per second, and overvoltage protection is included. In a workshop where other large machines start and stop, this is the cheapest insurance you can buy for the laser source and the control electronics.

Input voltage200 – 260 V, 5 kVA
Output voltage220 V ±3%
Correction speed> 15 V per second
Overvoltage protection245 ±5 V
Efficiencyabove 95%
Fume extraction filter

Fume extraction filter 1,279 €+ 549 €

A clean place to work

Extracts the smoke and particles produced above all by CO₂ cutting and engraving on wood, acrylic and leather. Filtration runs in three stages: a coarse pre-filter for large particles, a HEPA filter that captures the fine 0.25 – 0.5 micron particles that damage the lungs, and a layer of activated carbon that removes the smell. It has wheels and a handle, so it moves easily around the workshop.

Air flow400 m³/h
Filtration3 stages, HEPA and activated carbon
Power · supply300 W · 220 V
Noise≤ 55 dB
Size · weight420 × 320 × 580 mm · 25 kg
Consumables kit

Consumables kit + 200 €

No unplanned stops

Protective lenses, cutting nozzles and welding nozzles, enough for the first months of work. The protective lens is the part that gets dirty and wears out most often, and a worn nozzle degrades cut quality directly. Having them on the shelf from day one means you do not stop production for days waiting for a parcel to clear.

ContainsProtective lenses
Cutting nozzles
Welding nozzles
RecommendedFor the first months of production
The arguments that count

Four numbers worth remembering

5×

Faster than TIG

Laser welding sharply reduces the time per part compared with conventional welding.

15–30%

Material saved

Industrial nesting, common-line cutting and micro-joints.

1/5

Of the floor space

Compact enough for small workshops and short production runs.

6

Integrated processes

One machine instead of four separate ones.

Independent reviews

Unboxed. Tested. Works.

Two independent reviews, filmed by creators who work with laser equipment every day. These are not promotional materials but tests they ran on their own. The videos load only when you click, so the page stays fast.

M3 ULTRA tested in a workshop

M3 ULTRA tested in a workshop

The machine out of the crate, powered up and put to work on real material.

The six processes, one by one

The six processes, one by one

Cutting, welding, cleaning and engraving, each checked in turn.

Where it works

Typical applications

A solution for workshops that take small, varied orders: one machine covers cutting, welding, cleaning and engraving.

Metal fabrication

Metal fabrication

Fast cutting, quality seams and surface cleaning before painting.

Custom production

Custom production

Engraving on wood, leather or glass, and short runs for gifts and decorative work.

Small manufacturers

Small manufacturers

Replaces several machines, saves floor space and lowers the initial investment.

Prototyping

Prototyping

High accuracy on complicated parts, with no additional manual finishing.

Schools and training centres

Schools and training centres

Automatic CNC control and an accessible interface, suitable for beginners.

A clean process

A clean process

Low energy consumption, and laser cleaning produces no waste water.

What it actually cuts

Cutting capacity, material by material

Taken from the manufacturer’s parameter tables for this exact configuration: a 1200 W fibre source and a 130 W CO₂ tube. For metals the table separates what can be cut with air from the compressor and what needs bottled gas, because that difference shows up directly in running cost. In each pair of columns, the first figure is the thickness the machine works at in production; the second is a thickness the table still gives, but several times slower, so for occasional parts rather than batches.

Metals · 1200 W fibre, CNC head
MaterialWith air from the compressorWith bottled gas
in productionoccasionalin productionoccasional
Carbon steelabove 6 mm only with oxygen5 mm6 mm10 mm12 mm
Stainless steelnitrogen adds no thickness, but leaves an oxide-free edge5 mm6 mm5 mm6 mm
Aluminiumair reaches further than nitrogen here5 mm6 mm2 mm3 mm
Brassnitrogen adds no thickness2 mm3 mm2 mm3 mm

In short, about air. Air from the compressor covers everything the machine cuts, with one exception: carbon steel above 6 mm, which needs oxygen from a bottle. On stainless and brass, nitrogen buys no extra thickness over air — what it buys is an oxide-free edge, worth having where the part is painted or stays visible. On aluminium, air actually reaches further than nitrogen: 6 mm against 3 mm.

Non-metals · 130 W CO₂
MaterialIn productionOccasional
Acrylic15 mm25 mm
MDF10 mm15 mm
Woodrare hardwoods excepted10 mm12 mm
Rubber4 mm6 mm
Two-colour board2 mm—
Leather2 mm, single layer—
Fabric and papersingle layer—

Non-metals are cut with an air blast, so no bottles are involved.

The second column is for occasional work. At those thicknesses cutting speed drops several times against the column on the left, the edge comes out rougher, gas consumption rises and the nozzle wears faster. For parts that repeat, the first column is what can be relied on.

The figures above are for the CNC cutting head, the one that works on the bed. With the handheld cutting head the limit is 4 mm on carbon steel, stainless and aluminium, and 2 mm on brass, with nitrogen at 6 – 8 bar; there the operator’s hand sets the result, not the program, so that cut belongs to repairs and adjustments rather than production parts.

Welding · 1200 W fibre
MaterialIn productionOccasionalWire
Stainless steel3 mm4 mm0.8 – 1.2 mm
Carbon steel3 mm4 mm0.8 – 1.6 mm
Aluminium1.5 mm2 mm1.0 – 1.6 mm

Stainless and carbon steel up to 0.5 mm are welded butt to butt without filler wire. Shielding gas is nitrogen, at 20 l/min or more. At the thickness in the second column the manufacturer calls for noticeably more power, so more heat goes into the part and the risk of distortion rises on thin sheet or long seams.

All figures are indicative: they depend on material quality, on the gas and its pressure, on the state of the lens and on the nozzle in use. The air has to be dry and oil-free, otherwise the lenses foul; the screw compressor in the options list supplies certified oil-free air with a dryer and filters.

Technical data

Full specifications

Laser sources
Laser typeFibre laser + CO₂ laser
Laser power1200 W fibre + 130 W CO₂
Wavelength1080 ± 10 nm
Laser safety classClass 4
Capacity
FunctionsWelding · cutting · cleaning · CNC metal cutting · CO₂ cutting · CO₂ engraving
Welding thickness0.2 – 5 mm
Cutting thickness, CNC headCarbon steel up to 12 mm · stainless and aluminium up to 6 mm · brass up to 3 mm, with the 1200 W fibre
Cutting thickness, air onlyCarbon steel, stainless and aluminium up to 6 mm · brass up to 3 mm, with no bottles
Cutting thickness, handheld headUp to 4 mm on carbon steel, stainless and aluminium · 2 mm on brass
Cutting thickness, CO₂Acrylic up to 25 mm · MDF up to 15 mm · wood up to 12 mm, with the 130 W tube
Working area1380 × 920 mm
Maximum material width1380 mm
Maximum material thickness fed60 mm
Cylindrical parts (rotary device)Φ15 – 150 mm, up to 1200 mm long
Motion and accuracy
Maximum working speed800 mm/s
Repeat accuracy, X and Y±0.02 mm
Maximum acceleration1 G
Travel X / Y / Z1450 / 960 / 60 mm
Installation requirements
Power supply200 – 240 V AC, 50/60 Hz, single phase, approx. 5 kW
Assist gasNitrogen, argon or oxygen
CoolingAir cooling plus integrated water cooling
Operating temperature−10 °C to 40 °C
Cable length8 m
Dimensions and warranty
Dimensions620 × 355 × 610 mm (laser unit) + 2185 × 1780 × 1100 mm (table)
Weight610 kg
Warranty24 months machine · 12 months laser source and CO₂ tube
Delivered with the machine

What is in the crate

The machine arrives with everything you need to start: welding head, cutting head, wire feeder, safety accessories and documentation.

GWEIKE M3 ULTRA packing list

Buying from outside Romania

We are the official GWEIKE distributor in Romania and we ship across the European Union. The terms below are what we put in writing on every quotation, so there is nothing to discover after the order.

Delivery

The machine is sold EXW Bucharest, Romania. You may collect it yourself or, on request, we will send you a transport quotation to your delivery address anywhere in the European Union.

Delivery time

From stock when the configuration you choose is available in Bucharest, otherwise within 3 – 4 weeks of the order. The exact date is confirmed in the quotation.

VAT

Prices are quoted excluding VAT. For companies with a valid intra-community VAT number the invoice is issued under the reverse charge mechanism, so no Romanian VAT is charged.

Warranty

24 months on the machine and 12 months on the laser source and the CO₂ tube. Spare parts are shipped free of charge throughout the warranty period.

Setup and support

Installation is done by you, guided by a complete set of video tutorials. Whenever you need us, we provide remote assistance over WhatsApp and TeamViewer, connected directly to the machine.

Documentation

Manual, interface and video tutorials are in English. On request we can also supply the documentation translated into your own language.

Questions

What buyers abroad ask us

Can I buy it if my company is not in Romania?

Yes. We ship across the European Union. The machine leaves our warehouse in Bucharest, and you can either arrange collection yourself or ask us for a transport quotation to your address. For companies with a valid intra-community VAT number the invoice carries no Romanian VAT.

What is the delivery time?

If the configuration you choose is in stock in Bucharest, the machine ships immediately. Otherwise the delivery time is 3 to 4 weeks from the order. We confirm the exact date in the quotation, before you commit to anything.

Who installs it?

You do, and it is simpler than it sounds. The machine arrives assembled; what remains is positioning it, connecting power and assist gas, and running the first tests. We supply a full set of video tutorials covering every step, and if anything is unclear we connect to the machine remotely over TeamViewer while we talk on WhatsApp. Most of our customers are cutting on the first day.

What happens if something breaks under warranty?

Spare parts are shipped to you free of charge for the duration of the warranty. Diagnosis is done remotely, over TeamViewer connected to the machine, which in practice resolves most situations without anyone travelling. If an on-site intervention is genuinely necessary, we quote the technician's travel separately.

Which options are worth taking from the start?

The voltage stabiliser, on any installation: a fibre laser source is sensitive to mains fluctuation, and 349 € is cheap insurance for the most expensive component in the machine. The screw compressor, if you intend to cut metal regularly, because it lets you cut with air instead of bottled nitrogen and pays for itself in gas. The consumables kit, because protective lenses and nozzles wear out and waiting for a parcel means stopping production. The other two depend on your work: the rotary device only if you process round parts, the extraction filter mainly for CO₂ work on wood, acrylic or leather.

Does it need three-phase power?

No. It runs on 200 – 240 V single phase, 50/60 Hz, drawing roughly 5 kW. That is one of the reasons this machine fits workshops where a conventional fibre laser could not be installed without an electrical upgrade.

What can it actually weld?

Carbon steel, stainless steel, aluminium, copper, titanium and galvanised sheet, from 0.2 to 5 mm. On thin stainless and aluminium the advantage over TIG is largest: several times faster, a much narrower heat-affected zone, and far less distortion to correct afterwards.

In which language is the documentation?

The interface, the manual and the video tutorials are in English. If you would rather have them in your own language, tell us when you order: we translate the documentation with DeepL and deliver it in your language alongside the English original.

Tell us what you need to produce

Send us the materials and thicknesses you work with and we will tell you honestly whether this machine fits — including when the honest answer is that it does not. You will get a written quotation with the price, the delivery time and the delivery terms.

M3 ULTRA EN – contact heading
Last step

Send your configuration and get a firm quotation

The configuration you built above, with every option you ticked, is filled into the form automatically. Add your contact details and tell us where the machine would be delivered, and we reply within one working day with the price, the delivery time and a transport quotation to your address.

M3 ULTRA EN – contact panel

Talk to us before you order

Free consultation, in English. We tell you which options are worth taking from the start and which ones you can add later without paying for them now.

+40 723 190 249 Mon – Fri · 8:30 – 17:00 Romania time (UTC+2)
Landline: +40 21 223 03 45 · +40 21 223 03 91
Email: gweike@deltamail.ro
Office: Str. Pandele Țărușanu 8, Sector 1, Bucharest, Romania
Showroom: Bd. Metalurgiei, Bucharest · demonstrations by appointment
What you get from the conversation
  • We check whether the six processes really cover what you produce
  • We say which options are worth it and which can wait
  • You get the delivery time and a transport quotation to your address
  • You are welcome in our Bucharest showroom, with your own parts
Message us on WhatsApp